Triangular cardboard totem
The triangular cardboard totem is a three-sided advertising column, built from a single folded sheet of board. It stands on its own and carries your message over its full height, at eye level. Use it in a shop, in a reception area, at a trade show or during a promotion running for a few days.
- One size: 46.6 x 190 cm.
- 390 g board, rigid yet light to move.
- Three printed faces, readable from every approach.
Configure my product
Loading options…
Templates & instructions
Technical sheet
- Resolution
- 300 DPI
- Colours
- CMYK
- Bleed
- 2 mm
- Safety margin
- 4 mm
Which board is used for the triangular cardboard totem?
The triangular cardboard totem is made from 390 g board. That weight is the balance point of the product: rigid enough for a 190 cm column to stand up through its own geometry, light enough for one person to carry it across a shop floor. The board folds cleanly, holds sharp edges and goes into paper recycling once the campaign is over. On this material, flat colour and large images give the best result, so keep fine detail for the areas people read up close.
The size available
The totem comes in a single format, 46.6 x 190 cm. The height lifts your message above the shelving and makes it visible from a shop entrance or from an exhibition aisle. The width stays modest, so the column fits at the end of an aisle, in a corner of a lobby, beside a till or in front of a window without blocking the way.
Its triangular section gives three printed faces, so the totem reads from any approach. You can run a sequence across them — an offer, an explanation, a contact — or repeat one image three times so it always faces the visitor.
Preparing your artwork
300 DPI, CMYK, 2 mm of bleed and a 4 mm safety margin. Keep text away from the folds: a sentence running over an edge becomes unreadable as soon as the column is seen at an angle. Place the key information between 1.20 m and 1.60 m from the floor, the band the eye scans while walking, and leave secondary details for the lower part.
2M Numérique at your side
We print your triangular cardboard totem in our workshop in Manciet, in the Gers: 100% Made in Occitanie, in keeping with our responsible approach. It belongs to the advertising totem section of our exhibition stands range. Tell us about your campaign and we will work through the artwork with you.
Made here
94 % of our orders were produced in-house in 2024-2025, and 100 % in France. Our workshop is in Manciet, in the Gers, near Nogaro — recent machinery, local workshops. Less transport, faster turnaround.
Committed suppliers
We source our materials from regional partners who share our standards. Our main textile supplier is a French manufacturer whose site in Hagetmau, in the neighbouring Landes, supplies us through a short circuit — EcoVadis Platinum 2024, organic cotton and recycled textile ranges certified GOTS and GRS. Our paper comes from sustainably managed forests.
Less waste
PVC offcuts, paper and substrates are sorted and recovered; our adhesive films are available in recycled PVC. Nesting and imposition of files cut offcuts down: we print the right quantity. And low-impact inks, for prints that last.
A person, not a form
A close-knit team, from the first idea to the finished product. Every project, large or small, gets the same care. A question about your file? +33 5 33 13 02 01.
You might also like
LED light totem
From €211.20
Hanging banner sign
From €422.40
Elliptical cardboard totem
From €44.40
Photocall backdrop
From €184.80
Cardboard cube totem
From €52.80
Pop-up display stand
From €129.60
Premium fabric totem
From €130.80
Fabric display wall
From €237.60
Hanging banner
From €24.00
L-Banner stand
From €33.60
Curved PVC counter
From €50.40
Custom printed tablecloths
From €31.20
In the same category
Cardboard cube totem
From €52.80
Premium fabric totem
From €130.80
Elliptical cardboard totem
From €44.40